PhysicsClassical Physics

Knowledge guide

Buoyant Force and Apparent Weight: Measure Volume without Changing Mass

Connect Archimedes' principle, force balance, and density to interpret submerged scale readings and recognize the assumptions behind immersion measurements.

The fluid supports part of the load

Fluid pressure increases with depth. The pressure forces on an immersed object's surface combine into an upward buoyant force. For a fluid of approximately uniform density:

FB=ρfgVdisplaced.F_B=\rho_f gV_{\mathrm{displaced}}.

The density in this formula belongs to the fluid, not the object. The displaced volume is the submerged volume. It equals the object's total volume only for complete immersion.

A scale reads support force

For an object hanging motionless from a scale, with no contact with the container:

T+FB=mg,T=mg−FB.T+F_B=mg,\qquad T=mg-F_B.

Its gravitational weight mgmg is unchanged by moving it into water. The scale reads a smaller tension because the fluid supplies some support. If the scale displays kilograms, its apparent mass reading is T/gT/g; that reading is not the object's actual mass.

When buoyancy in air is neglected:

FB=Wair−Wfluid,V=Wair−Wfluidρfg.F_B=W_{\mathrm{air}}-W_{\mathrm{fluid}},\qquad V=\frac{W_{\mathrm{air}}-W_{\mathrm{fluid}}}{\rho_f g}.

For mass-calibrated readings mairm_{\mathrm{air}} and mappm_{\mathrm{app}}:

V=mair−mappρf,ρobject=ρfmairmair−mapp.V=\frac{m_{\mathrm{air}}-m_{\mathrm{app}}}{\rho_f},\qquad \rho_{\mathrm{object}}=\rho_f\frac{m_{\mathrm{air}}}{m_{\mathrm{air}}-m_{\mathrm{app}}}.

A new force-reading example

A solid sample hangs from a scale that reads 7.84 N in air and 4.90 N when completely immersed in freshwater. Take g=9.80 m/s2g=9.80\ \mathrm{m/s^2} and ρf=1000 kg/m3\rho_f=1000\ \mathrm{kg/m^3}.

The upward buoyant force is 7.84−4.90=2.94 N7.84-4.90=2.94\ \mathrm{N}. Its volume is:

V=2.941000(9.80)=3.00×10−4 m3=300 cm3.V=\frac{2.94}{1000(9.80)}=3.00\times10^{-4}\ \mathrm{m^3}=300\ \mathrm{cm^3}.

The actual mass is 7.84/9.80=0.800 kg7.84/9.80=0.800\ \mathrm{kg}, so its average density is approximately 2.67×103 kg/m32.67\times10^3\ \mathrm{kg/m^3}. Replacing the actual mass with 4.90/9.804.90/9.80 would underestimate the density.

When the difference method needs correction

Partial immersion measures only the submerged volume. Trapped bubbles add displaced volume; water entering pores may change what volume the measurement represents. Contact with the bottom adds another support force, invalidating the simple tension balance.

If air buoyancy matters, the difference between air and liquid readings is (ρf−ρair)gV(\rho_f-\rho_{\mathrm{air}})gV, assuming the same displaced volume in both. Use that correction rather than interpreting the reading difference as the liquid buoyancy alone.

For a freely floating object with no other vertical forces, buoyancy balances weight. An object held completely submerged need not satisfy FB=mgF_B=mg because the support tension also contributes.

Related question

Apply this knowledge

Use the concept guide to understand the reasoning, then return to the complete question and worked answer.

Buoyant Force: Density of a Rock Weighed in Air and Water

Sources

These references support the core concepts and interpretation boundaries explained above.